Looking for:
One moment, please - All replies |
Possible latency with Source-Connect Link and Logic Pro X - Source Elements - Adjust the I/O buffer size
I use Logic Pro X Is that possible? I think I hooked everything up correctly And Frree saw a signal on meter. Or am I missing something? Update File information seems to help clean things up and getting rid of unused files also seems to refresh the sessions. I just saw all these help videos with people.
Am I missing something here! If you do it and get 0, that's nice it means your Saphire audio driver is reporting what the actual RTL is. But there is still some round trip latency, as reported in the audio prefs for loic buffer size.
Kogic, regarding playback and recording and latency. And that does work. Then if they are still not as you remember recording them, then go look at the recorded regions under a microscope and you will probably find ,ogic stuff was recorded to the track a little early or late.
There is something like перейти на источник record offset привожу ссылку is calculated by LPX when you record audio and midi tracks. It takes into account the reported RTL as is reported in the audio preferences for the buffer size Then it attempts to recalculate this record offset in order to place the ,ogic on the timeline correctly according to what it thought you heard as you were recording.
There are advanced tricky ways to setup AUX bus FX to use in combination with hardware direct monitoring, but its a little more complicated to explain and most likely you will have audible sonic artifacts that way you probably won't like. Because I work as songwriter these days as well and use a lot soft synthsI have started leaving the software loogic on.
It would be simple to stop doing that. The problem is that I have also started giving my singers rev and delay to track to. My method has been to lahency an aux ch. There basically seems to rree a tipping point that is hard to predict once you start running more than a few plugins. It sounds like bouncing the mix down is the most sure fire solution.
You can turn off software monitoring and listen to the dry vocals with direct hardware monitoring. Around 10ms they will start to hear combing, logic pro x latency test free and other artifacts.
If there are any plugins with latency on aux or output channels anywhere in the project it can be made worse. Avoid output channel logic pro x latency test free plugins too. Your best bet is to bounce a mix lahency the vocalist and use no software instruments while you track.
So leave it set to zero. However plugins on aux channels while recording can cause a lot of delays, if they are latent, confusion and incorrect record offset. And that /15719.txt can turn the software monitoring off. I realize that the rev plugin on my newly created aux may also be latent. When I look at the mix I was tracking to now, I really did have a lot more prro on that I thought even had a multi on the master bus eek!
Too many projects and not enough sleep. But thank you for all the advice. Your direct monitoring will hear the dry sound. Another alternative to the above is something I am calling hybrid monitoring. If you do it that way, then you will twst "hear" a delay between the dry and wet sound.
However the singer may logic pro x latency test free a delay between their own voice and the sound in перейти headphones The record offset will be when they sang tree though, which i think is a good thing. Singers using headphones can complain that they can hear sonic artifacts in their inner ear such as flanging and what not ,if the logic pro x latency test free between when they sing it and when they latenc it is logic pro x latency test free than 10ms So which compromise is the best rfee I'm not really sure and would love to hear your feedback after you try it.
Might depend on the singer. Might depend on what reverb you're using. Might tend on how much audio card latency you have too. One way can have sonic artifacts between their dry and wet sound, as well as sonic loyic between their inner ear and the wet sound.
The second hybrid logic pro x latency test free will make sure what they hear is clean in sync between wet and dry, but their inner ear will out of sync with both dry and wet. Ideally, you should just try laency eliminate all latency logic pro x latency test free much as you can when recording because there is just no magic bullet to get rid of these problems. Use a temporary zero latency reverb plugin, for example, and as others logic pro x latency test free, run the audio buffer as small as your can get away with.
Good tset. Lucky to have met you here. Juggling a lot balls right now. There are plenty of plugins out there that incur no extra latency. Try to use those while tracking vocals, you can always swap them out later with your favorite, but latent, reverb plugin later. How is that possible? You can post now and register later. If you have an account, sign in now to post with your account. Restore formatting. Only 75 emoji are allowed. Display as a link instead. Clear editor. Upload or insert images from URL.
By velanche3 hours ago in Logic Pro. By jeremyqwertyOctober 28 in Logic Pro. By aldudeprl hours ago in Logic Pro. By kenrob2 hours ago in Logic Pro. Share More sharing options Followers 1. Reply to this topic Start new topic. Recommended Posts. ReaghSweden Posted Перейти на источник 21, Posted February 21, Link to comment Share on other sites More sharing options Dewdman42 Posted February 21, This is a complicated issue.
Again thank you for your основываясь на этих данных and thoughtful reply. Posted February 21, edited. Then you will hear both. The dry audio recording will be sample accurate that way. Avoid output channel latency plugins too Edited February 21, by Dewdman And yes if you have fre mix using latent aux channels then bouncing down those will help a lot before recording vocals.
You can also change the lateny mode to audio and software instrument tracks instead of all, which may lessen the delay on the whole project but your entire mix could be laency of sync, all the aux channels will be delayed behind the source tracks.
Dewdman42 Posted February 22, loyic Posted February 22, ReaghSweden Posted February 22, адрес страницы Again thank you.
Now, at least, I have some real knowledge on the subject which always helps. Thanks again. Good logic pro x latency test free. Join the conversation You can post now and register later. Reply to this topic Insert image from URL.
Go to topic listing. All my plugins not together in one list logic pro x latency test free only show on certain tracks so I can't use them. Routing issues lgic Logic By aldude2 hours ago logic pro x latency test free Logic Pro. Midii automation issue By kenrob2 hours ago in Logic Pro midi automation. Sign In Sign Up.
No comments:
Post a Comment